Sailboat Requirements
Hull Kind: Keel/Cbrd.
Rigging Variety: Gaffhead Sloop
Size over-all: 22’6″ 6.858m
Length about deck: 19’3” 5.867m
Size of waterline: 17’7″ 5.334m
Beam: 7’2” 2.184m
Draught:1’6” – 4’0”0.457m – 1.219m
Displacement:2350lb1065kg
Ballast: 700 lb / 318 kg
Sail space:194ft218.02m2
Approx towing pounds:3300lb1500kg
RCD categoryC
S.A./Disp.: 17.60
Bal./Disp.: 29.79
Disp./Len.: 195.75
Construction: GRP
Designer: Roger Dongray
To start with Designed: 1979
# Built: 1000
Builder
Cornish Crabbers LLP
Device 5, Bess Park Road
Wadebridge
Cornwall
PL27 6HB
Phone: +44 ()1208 862 666
Electronic mail: facts@cornishcrabbers.co.uk
Auxiliary Energy/Tanks (orig. equip.)
Make: Yanmar (decide.)
Model: Yanmar 1GM10 9hp
Sort: Diesel
Sailboat Calculations
S.A./Disp.: 17.60
Bal./Disp.: 29.79
Disp./Len.: 195.75
Comfort and ease Ratio: 14.60
Capsize Screening Formulation: 2.16
Shrimper 19 conventional sail away specification
Hull Design: Hand laid strong GRP hull with no foam main. Integral centerplate case laminated as aspect of the full hull composition. Interior bunk and
forepeak moulding bonded into hull with inside structural bulkheads bonded to both equally hull and deck mouldings. Conventional colours are off white, darkish blue
or dark inexperienced. The hull and deck joint is by way of an overlap or ‘Biscuit Tin Lid’ with GRP bonding.
Rudder: The rudder is transom hung on two stainless steel hangings bolted through the transom with Hardwood backing pads. The rudder is produced
from laminated plywood with a stainless steel lifting drop plate.
Engine Beds: Engine beds are included in the GRP bunk moulding with delicate steel mounts bonded into the mattress style and design which incorporates an oil drip tray.
Ballast: Ballast is by way of iron punchings encapsulated in resin within the hull keel moulding. A galvanised steel centerplate kinds component of the ballast
with a stainless steel lifting wire main to a winch lifting technique operated from the cockpit.
Boot Best: A single boot top moulded in gel coat located above antifouling degree. Colour in distinction to most important hull and typically matching the deck.
Deck Building: Hand laid GRP with Balsa main in way of horizontal load spots. Difficult wooden pads beneath deck fittings and worry factors.
Cockpit : Cockpit locker lids are hand laid with Balsa main. There is integrated non slip on horizontal surfaces with an optional two tone colour. A cockpit
drain is located in the heart of the main foot effectively with further drainage from the seats. A central watertight locker offers common storage or houses the
diesel engine when fitted.
Deck Fittings: Bespoke deck fittings like bowsprit, tabernacle and chain plates are manufactured from stainless metal. 4 aluminium deck cleats are positioned
aft & amidships with two fairleads feeding a teak Sampson submit forward. All sail controls are led aft to rope clutches / jammers with a one halyard
winch to starboard. Adjustable jib & mainsheet automobiles. Accessibility under is by means of a teak lined sliding companionway hatch and split plywood / Perspex washboards.
More air flow delivered by an aluminium ahead hatch.
Ports: 2 aluminium fastened ports are fitted 1 every single in the hull topsides.
Chain plates: Chain plates are in stainless metal and by way of bolted on the hull sides.
Vents: Ventilation is by means of a washboard vent and opening ahead hatch.
Miscellaneous Gear: Fuel filler &tank vent.(Inboard edition only), Life harness attachment place by the companionway, Rope tidies for halyards.
Cockpit Lockers: Two major watertight lockers with latches and padlocks are offered. A padlock is also offered for the companionway hatch.
Mainmast: Laminated in Sitka Spruce and dealt with with Sikkens Cetol such as a stainless steel mast band to just take Cap shrouds, jib and mainsail halyards.
All deck mounted on a substantial stainless steel tabernacle.
Primary Increase: Laminated in Sitka Spruce and addressed with Sikkens Cetol like a Stainless steel gooseneck fitting, kicker and mainsheet bands and all
associated reefing line qualified prospects / terminals.
Bowsprit: Laminated in Sitka Spruce and handled with Sikkens Cetol which includes a Stainless steel pivot fitting, end plate and bobstay just take off details.
Gaff: Laminated in Sitka Spruce and taken care of with Sikkens Cetol together with a Stainless steel gaff collar with rubber protection on bearing surface area. Wire hoist
span and block.
Standing Rigging: Cap shrouds, lessen shrouds & forestay in 4mm 1 x 19 stainless steel wire with swagged finishes. Chromed rigging screws. Jib mounted on
reefing spar and controls led aft to cockpit.
Managing Rigging: Most important throat / peak halyards – 6mm braid. Jib &Staysail halyards – 6mm braid. Main topping lift – 6mm braid. Mainsail reefing strains –
6mm braid. Mainsail outhaul – 6mm braid. Mainsheet & Jib sheets – 10mm sheet rope. All connected blocks for buy tackles.
Mainsail: Dacron in tan or cream. 2 reef points with tie in lacing. Luff and gaff lacing as necessary.
Jib: Dacron in tan or cream with wire luff and tell tails.
Increase Address: In maroon, or cream acrylic. Fixings to allow for for topping carry and mainsheet acquire off. All sails provided with, sail numbers, symbol and ties.
Engineering
Outboard Model
Outboard properly: A teak engine mounting with stainless brackets. Engine nicely hull blank. GRP moulded gas tank stowage and gasoline guide splitter by way of aft
locker compartment. (gas guide not equipped as normal)
Inboard Model
Stern Gear: A 1” stainless metal shaft is equipped, related to the motor by using a coupling and fitted with a Tides Maritime ‘lip seal’ gland. The shaft drives a mounted
2-bladed propeller.
Engine: Yanmar 1GM10 9hp marine diesel motor. A 55 amp (12V) alternator is equipped to the motor.
Engine Instruments and Controls: The engine devices are situated at the rear of the cockpit coaming and are recessed with a distinct go over. Instruments
contain audible alarm, alternator warning mild, start change and prevent management. A solitary lever motor handle is supplied and equipped in the cockpit nicely.
Engine Cooling: The motor is specifically salt water cooled. A 1/2″ diameter pipe prospects from the principal seawater inlet through a strainer to the motor and
discharges overboard by means of the exhaust.
Motor Exhaust: A versatile exhaust hose connects the exhaust through a swan neck with water trap to the outlet fitting through the transom.
Gasoline Technique: A plastic diesel tank with a capability of approximately 18 litres, breather and integrated fuel gauge. The tank is equipped with stream and return
lines, the movement line acquiring a manual shut off valve.
Plumbing
Bilge Procedure: 1 x Manual bilge pump operated from the cockpit with a take care of saved in the aft locker.
Refreshing H2o Tanks: 2 x 10ltr plastic jerry cans with guide hand pump. Also a bucket / sink.
Soil Program: When equipped the heads discharge right to sea by way of a vent loop and skin fitting.
Inlet / Outlet Fittings: Motor: In via a solitary skin fitting with a valve and strainer, out through the exhaust procedure.
Gasoline Process: There is a double burner hob cooker hooked up to a independently stored gasoline bottle.
12 volt DC process
Batteries: Motor – one particular 12 volt 55 amp/hour. (Optional on outboard edition)
Charging: Through main motor – a 35 amp (at 12 volt) alternator.
Switchboard: An optional change panel is fitted to boats that have more electronics fitted.
Miscellaneous Common Tools
Deck: 1 x winch deal with. 1 x bilge pump cope with. Stowed in aft cockpit locker. 1 x fire extinguisher – situated down below.
Joinery: The inside joinery is created from large quality materials and in accordance with great yacht practice. Bulkheads and facet back linings are
from plywood.
Finish: All cabin woodwork is completed in a blend of painted bulkheads and varnished trim.
Soles: Rubber textured sole throughout.
Upholstery: A decision of gentle or wipe down plastic upholstery is available.
Posted by The Shaldives on 2022-08-18 18:54:48
Tagged: , 2022 , absorbing , bateau , bateaux , Boats , compelling , compulsive , Cornish Shrimper 19 , Devon , England , engrossing , Europe , EX3 , Exe Estuary , Exeter , fascinating , flicker , flicker image , Fogwill , GB , GBR , Good Britan , gripping , Male , Male Fogwill , Historic , Maritime , Nautical , picture , Regnum , River , River Exe , riveting , Roger Dongray , Sail Number 78 , sony , south of england , South West , impressive , the shaldives , Toppeshamme , Topsham , Topsham Turf Ferry , Uk , United Kingdom , Vessel , yachting , Yachts
#furniture #Do it yourself #woodwork #woodworking #freedownload#woodworkingprojects #woodsmith ,wooden craft, wooden planer, good woodworking, wood chairs, wood doing work equipment, well known woodworking, woodworking publications, woodworking workbench ideas
