Tag: GBTNM

SPECIFICATION

Size overall: 22’6″6.858m
Size above deck: 19’3”5.867m
Size of waterline: 17’7″5.334m
Beam: 7’2”2.184m
Draught:1’6” – 4’0”0.457m – 1.219m
Displacement: 2350lb1065kg
Sail location: 194ft218.02m2
Approx towing weight:3300lb1500kg
RCD categoryC
Shrimper 19 common sail away specification
Hull Construction: Hand laid good GRP hull with no foam main. Integral centerplate situation laminated as part of the comprehensive hull composition. Internal bunk and
forepeak moulding bonded into hull with internal structural bulkheads bonded to each hull and deck mouldings. Normal colours are off white, darkish blue
or darkish environmentally friendly. The hull and deck joint is by way of an overlap or ‘Biscuit Tin Lid’ with GRP bonding.
Rudder: The rudder is transom hung on two stainless steel hangings bolted by means of the transom with Hardwood backing pads. The rudder is constructed
from laminated plywood with a stainless metal lifting fall plate.
Motor Beds: Motor beds are included in the GRP bunk moulding with gentle metal mounts bonded into the bed layout which incorporates an oil drip
tray.
Ballast: Ballast is by way of iron punchings encapsulated in resin inside of the hull keel moulding. A galvanised metal centerplate varieties section of the ballast
with a stainless metal lifting wire main to a winch lifting method operated from the cockpit.
Boot Top: A single boot top moulded in gel coat located above antifouling amount. Colour in distinction to main hull and generally matching the deck.
Deck Building: Hand laid GRP with Balsa core in way of horizontal load parts. Tricky wooden pads less than deck fittings and anxiety points.
Cockpit : Cockpit locker lids are hand laid with Balsa core. There is built-in non slip on horizontal surfaces with an optional two tone color. A cockpit
drain is found in the heart of the key foot very well with more drainage from the seats. A central watertight locker presents typical storage or residences the
diesel engine when equipped.
Deck Fittings: Bespoke deck fittings like bowsprit, tabernacle and chain plates are produced from stainless metal. 4 aluminium deck cleats are positioned
aft & amidships with two fairleads feeding a teak Sampson article forward. All sail controls are led aft to rope clutches / jammers with a one halyard
winch to starboard. Adjustable jib & mainsheet cars and trucks. Obtain beneath is by way of a teak lined sliding companionway hatch and split plywood / Perspex washboards.
More ventilation offered by an aluminium ahead hatch.
Ports: 2 aluminium fastened ports are equipped a single every single in the hull topsides.
Chain plates: Chain plates are in stainless steel and by means of bolted on the hull sides.
Vents: Ventilation is by using a washboard vent and opening ahead hatch.
Miscellaneous Equipment: Gas filler &tank vent.(Inboard model only), Lifetime harness attachment level by the companionway, Rope tidies for halyards.
Cockpit Lockers: Two principal watertight lockers with latches and padlocks are presented. A padlock is also presented for the companionway hatch.
Mainmast: Laminated in Sitka Spruce and treated with Sikkens Cetol like a stainless steel mast band to take Cap shrouds, jib and mainsail halyards.
All deck mounted on a significant stainless metal tabernacle.
Key Growth: Laminated in Sitka Spruce and treated with Sikkens Cetol such as a Stainless steel gooseneck fitting, kicker and mainsheet bands and all
affiliated reefing line qualified prospects / terminals.
Bowsprit: Laminated in Sitka Spruce and treated with Sikkens Cetol together with a Stainless steel pivot fitting, close plate and bobstay take off factors.
Gaff: Laminated in Sitka Spruce and addressed with Sikkens Cetol such as a Stainless steel gaff collar with rubber defense on bearing surface. Wire hoist
span and block.
Standing Rigging: Cap shrouds, reduce shrouds & forestay in 4mm 1 x 19 stainless metal wire with swagged finishes. Chromed rigging screws. Jib mounted on
reefing spar and controls led aft to cockpit.
Running Rigging: Major throat / peak halyards – 6mm braid. Jib &Staysail halyards – 6mm braid. Main topping elevate – 6mm braid. Mainsail reefing lines –
6mm braid. Mainsail outhaul – 6mm braid. Mainsheet & Jib sheets – 10mm sheet rope. All connected blocks for buy tackles.
Mainsail: Dacron in tan or cream. 2 reef points with tie in lacing. Luff and gaff lacing as needed.
Jib: Dacron in tan or product with wire luff and inform tails.
Increase Protect: In maroon, or cream acrylic. Fixings to let for topping elevate and mainsheet choose off. All sails supplied with, sail quantities, logo and ties.
Engineering
Outboard Variation
Outboard very well: A teak engine mounting with stainless brackets. Engine effectively hull blank. GRP moulded gasoline tank stowage and gasoline guide splitter as a result of aft
locker compartment. (fuel lead not supplied as conventional)
Inboard Edition
Stern Gear: A 1” stainless metal shaft is equipped, linked to the engine by means of a coupling and equipped with a Tides Maritime ‘lip seal’ gland. The shaft drives a preset
2-bladed propeller.
Motor: Yanmar 1GM10 9hp maritime diesel motor. A 55 amp (12V) alternator is fitted to the engine.
Motor Instruments and Controls: The engine devices are located at the rear of the cockpit coaming and are recessed with a apparent protect. Devices
involve audible alarm, alternator warning light, commence switch and end control. A solitary lever motor control is equipped and equipped in the cockpit perfectly.
Motor Cooling: The engine is directly salt h2o cooled. A 1/2″ diameter pipe prospects from the key seawater inlet by way of a strainer to the motor and
discharges overboard by means of the exhaust.
Engine Exhaust: A adaptable exhaust hose connects the exhaust by using a swan neck with drinking water trap to the outlet fitting via the transom.
Gasoline System: A plastic diesel tank with a capacity of somewhere around 18 litres, breather and integrated fuel gauge. The tank is fitted with flow and return
lines, the flow line owning a guide shut off valve.
Plumbing
Bilge Technique: 1 x Handbook bilge pump operated from the cockpit with a take care of saved in the aft locker.
New Drinking water Tanks: 2 x 10ltr plastic jerry cans with manual hand pump. Also a bucket / sink.
Soil Technique: When fitted the heads discharge straight to sea by means of a vent loop and pores and skin fitting.
Inlet / Outlet Fittings: Motor: In by way of a one pores and skin fitting with a valve and strainer, out by means of the exhaust program.
Fuel Technique: There is a double burner hob cooker hooked up to a independently saved gasoline bottle.
12 volt DC technique
Batteries: Engine – one particular 12 volt 55 amp/hour. (Optional on outboard edition)
Charging: By way of most important motor – a 35 amp (at 12 volt) alternator.
Switchboard: An optional swap panel is fitted to boats that have further electronics equipped.
Miscellaneous Normal Tools
Deck: 1 x winch take care of. 1 x bilge pump handle. Stowed in aft cockpit locker. 1 x hearth extinguisher – located down down below.
Joinery: The inside joinery is built from significant excellent materials and in accordance with fantastic yacht apply. Bulkheads and facet back linings are
from plywood.
Finish: All cabin woodwork is completed in a mix of painted bulkheads and varnished trim.
Soles: Rubber textured sole all over.
Upholstery: A decision of comfortable or wipe down plastic upholstery is obtainable.

Posted by The Shaldives on 2021-09-18 17:43:15

Tagged: , 2021 , ABP , Arwen , Associated British Ports , bateau , bateaux , Bâteaux , Seashore , Boat , Boats , Coastal , Coastal Waters , Coastline , powerful , compulsive , cornish crabbers , Cornish Shrimper 19 , Devon , Docks , DSC-HX60 , England , Europe , flicker , Fogwill , GB , GBR , GBTNM , Great Britan , Guy , Person Fogwill , Harbour , interesting , Maritime , Maritime , Nautical , PLAGE , River , River Teign , Rowsell Cornish Shrimper Sails , Sail Range 865 , Sailing Vessel , September , septembre , Shaldon , sony , Sony DSC-HX60 , South West , amazing , Summer season , Teign Estuary , Teignbridge , Teignmouth , Teignmouth (Methods) , the shaldives , TQ14 , United kingdom , United Kingdom , Yacht , Yachts

#furniture #Diy #woodwork #woodworking #freedownload#woodworkingprojects #woodsmith ,wood craft, wooden planer, good woodworking, wood chairs, wood functioning resources, preferred woodworking, woodworking books, woodworking workbench programs

SPECIFICATION

Length total: 22’6″6.858m
Size more than deck: 19’3”5.867m
Length of waterline: 17’7″5.334m
Beam: 7’2”2.184m
Draught:1’6” – 4’0”0.457m – 1.219m
Displacement: 2350lb1065kg
Sail area: 194ft218.02m2
Approx towing bodyweight:3300lb1500kg
RCD categoryC
Shrimper 19 conventional sail away specification
Hull Construction: Hand laid strong GRP hull with no foam main. Integral centerplate scenario laminated as part of the complete hull construction. Interior bunk and
forepeak moulding bonded into hull with interior structural bulkheads bonded to the two hull and deck mouldings. Standard colors are off white, dark blue
or darkish green. The hull and deck joint is by way of an overlap or ‘Biscuit Tin Lid’ with GRP bonding.
Rudder: The rudder is transom hung on two stainless metal hangings bolted through the transom with Hardwood backing pads. The rudder is created
from laminated plywood with a stainless metal lifting fall plate.
Engine Beds: Engine beds are included in the GRP bunk moulding with gentle metal mounts bonded into the bed design and style which incorporates an oil drip
tray.
Ballast: Ballast is by way of iron punchings encapsulated in resin inside of the hull keel moulding. A galvanised steel centerplate sorts component of the ballast
with a stainless metal lifting wire primary to a winch lifting process operated from the cockpit.
Boot Major: A one boot top moulded in gel coat situated earlier mentioned antifouling level. Colour in contrast to most important hull and usually matching the deck.
Deck Development: Hand laid GRP with Balsa main in way of horizontal load areas. Difficult wooden pads under deck fittings and stress details.
Cockpit : Cockpit locker lids are hand laid with Balsa core. There is integrated non slip on horizontal surfaces with an optional two tone colour. A cockpit
drain is positioned in the middle of the principal foot effectively with further drainage from the seats. A central watertight locker delivers standard storage or residences the
diesel engine when equipped.
Deck Fittings: Bespoke deck fittings which includes bowsprit, tabernacle and chain plates are produced from stainless metal. 4 aluminium deck cleats are positioned
aft & amidships with two fairleads feeding a teak Sampson write-up forward. All sail controls are led aft to rope clutches / jammers with a single halyard
winch to starboard. Adjustable jib & mainsheet cars and trucks. Obtain below is via a teak lined sliding companionway hatch and split plywood / Perspex washboards.
Extra air flow presented by an aluminium forward hatch.
Ports: 2 aluminium fixed ports are fitted one every in the hull topsides.
Chain plates: Chain plates are in stainless metal and via bolted on the hull sides.
Vents: Ventilation is by way of a washboard vent and opening ahead hatch.
Miscellaneous Tools: Fuel filler &tank vent.(Inboard edition only), Existence harness attachment stage by the companionway, Rope tidies for halyards.
Cockpit Lockers: Two main watertight lockers with latches and padlocks are offered. A padlock is also provided for the companionway hatch.
Mainmast: Laminated in Sitka Spruce and treated with Sikkens Cetol such as a stainless steel mast band to get Cap shrouds, jib and mainsail halyards.
All deck mounted on a considerable stainless steel tabernacle.
Major Growth: Laminated in Sitka Spruce and treated with Sikkens Cetol together with a Stainless steel gooseneck fitting, kicker and mainsheet bands and all
linked reefing line leads / terminals.
Bowsprit: Laminated in Sitka Spruce and handled with Sikkens Cetol including a Stainless metal pivot fitting, end plate and bobstay acquire off details.
Gaff: Laminated in Sitka Spruce and taken care of with Sikkens Cetol including a Stainless metal gaff collar with rubber safety on bearing area. Wire hoist
span and block.
Standing Rigging: Cap shrouds, reduced shrouds & forestay in 4mm 1 x 19 stainless metal wire with swagged finishes. Chromed rigging screws. Jib mounted on
reefing spar and controls led aft to cockpit.
Running Rigging: Key throat / peak halyards – 6mm braid. Jib &Staysail halyards – 6mm braid. Key topping lift – 6mm braid. Mainsail reefing strains –
6mm braid. Mainsail outhaul – 6mm braid. Mainsheet & Jib sheets – 10mm sheet rope. All connected blocks for purchase tackles.
Mainsail: Dacron in tan or product. 2 reef factors with tie in lacing. Luff and gaff lacing as expected.
Jib: Dacron in tan or cream with wire luff and notify tails.
Boom Address: In maroon, or cream acrylic. Fixings to allow for for topping carry and mainsheet take off. All sails equipped with, sail quantities, symbol and ties.
Engineering
Outboard Version
Outboard nicely: A teak motor mounting with stainless brackets. Engine nicely hull blank. GRP moulded gas tank stowage and fuel lead splitter as a result of aft
locker compartment. (gasoline lead not provided as conventional)
Inboard Variation
Stern Equipment: A 1” stainless steel shaft is fitted, linked to the motor through a coupling and fitted with a Tides Maritime ‘lip seal’ gland. The shaft drives a fixed
2-bladed propeller.
Engine: Yanmar 1GM10 9hp marine diesel engine. A 55 amp (12V) alternator is fitted to the motor.
Motor Devices and Controls: The motor instruments are located at the rear of the cockpit coaming and are recessed with a clear include. Instruments
contain audible alarm, alternator warning light, start off change and stop command. A single lever motor control is equipped and equipped in the cockpit effectively.
Engine Cooling: The engine is straight salt drinking water cooled. A 1/2″ diameter pipe potential customers from the major seawater inlet as a result of a strainer to the motor and
discharges overboard by way of the exhaust.
Motor Exhaust: A adaptable exhaust hose connects the exhaust by means of a swan neck with h2o lure to the outlet fitting as a result of the transom.
Gas Program: A plastic diesel tank with a ability of around 18 litres, breather and built-in fuel gauge. The tank is equipped with stream and return
strains, the circulation line acquiring a manual shut off valve.
Plumbing
Bilge Program: 1 x Manual bilge pump operated from the cockpit with a handle stored in the aft locker.
Fresh Water Tanks: 2 x 10ltr plastic jerry cans with manual hand pump. Also a bucket / sink.
Soil Procedure: When fitted the heads discharge right to sea through a vent loop and pores and skin fitting.
Inlet / Outlet Fittings: Engine: In by way of a solitary skin fitting with a valve and strainer, out through the exhaust method.
Gasoline System: There is a double burner hob cooker hooked up to a separately stored gas bottle.
12 volt DC method
Batteries: Engine – just one 12 volt 55 amp/hour. (Optional on outboard model)
Charging: By using most important engine – a 35 amp (at 12 volt) alternator.
Switchboard: An optional change panel is equipped to boats that have supplemental electronics fitted.
Miscellaneous Standard Machines
Deck: 1 x winch handle. 1 x bilge pump deal with. Stowed in aft cockpit locker. 1 x fireplace extinguisher – located down underneath.
Joinery: The inside joinery is produced from higher high-quality products and in accordance with very good yacht observe. Bulkheads and facet back again linings are
from plywood.
End: All cabin woodwork is concluded in a blend of painted bulkheads and varnished trim.
Soles: Rubber textured sole through.
Upholstery: A preference of gentle or wipe down plastic upholstery is obtainable.

Posted by The Shaldives on 2021-09-18 17:43:09

Tagged: , 2021 , ABP , Arwen , Linked British Ports , bateau , bateaux , Bâteaux , Seashore , Boat , Boats , Coastal , Coastal Waters , Shoreline , persuasive , compulsive , cornish crabbers , Cornish Shrimper 19 , Devon , Docks , DSC-HX60 , England , Europe , flicker , Fogwill , GB , GBR , GBTNM , Excellent Britan , Guy , Male Fogwill , Harbour , exciting , Maritime , Maritime , Nautical , PLAGE , River , River Teign , Rowsell Cornish Shrimper Sails , Sail Selection 865 , Sailing Vessel , September , septembre , Shaldon , sony , Sony DSC-HX60 , South West , magnificent , Summer , Teign Estuary , Teignbridge , Teignmouth , Teignmouth (Ways) , the shaldives , TQ14 , British isles , United Kingdom , Yacht , Yachts

#household furniture #Diy #woodwork #woodworking #freedownload#woodworkingprojects #woodsmith ,wood craft, wooden planer, wonderful woodworking, wood chairs, wooden functioning tools, common woodworking, woodworking textbooks, woodworking workbench options

SPECIFICATION

Duration in general: 22’6″6.858m
Size around deck: 19’3”5.867m
Duration of waterline: 17’7″5.334m
Beam: 7’2”2.184m
Draught:1’6” – 4’0”0.457m – 1.219m
Displacement: 2350lb1065kg
Sail spot: 194ft218.02m2
Approx towing pounds:3300lb1500kg
RCD categoryC
Shrimper 19 standard sail away specification
Hull Building: Hand laid strong GRP hull with no foam core. Integral centerplate circumstance laminated as section of the entire hull composition. Interior bunk and
forepeak moulding bonded into hull with internal structural bulkheads bonded to equally hull and deck mouldings. Normal colours are off white, dark blue
or dim inexperienced. The hull and deck joint is by way of an overlap or ‘Biscuit Tin Lid’ with GRP bonding.
Rudder: The rudder is transom hung on two stainless metal hangings bolted by the transom with Hardwood backing pads. The rudder is created
from laminated plywood with a stainless metal lifting drop plate.
Engine Beds: Engine beds are included in the GRP bunk moulding with delicate steel mounts bonded into the bed design which incorporates an oil drip
tray.
Ballast: Ballast is by way of iron punchings encapsulated in resin inside the hull keel moulding. A galvanised steel centerplate varieties part of the ballast
with a stainless metal lifting wire major to a winch lifting method operated from the cockpit.
Boot Top: A one boot top moulded in gel coat situated previously mentioned antifouling level. Color in contrast to major hull and ordinarily matching the deck.
Deck Design: Hand laid GRP with Balsa main in way of horizontal load spots. Tough wooden pads below deck fittings and strain factors.
Cockpit : Cockpit locker lids are hand laid with Balsa main. There is integrated non slip on horizontal surfaces with an optional two tone color. A cockpit
drain is found in the centre of the major foot nicely with more drainage from the seats. A central watertight locker delivers common storage or residences the
diesel motor when equipped.
Deck Fittings: Bespoke deck fittings such as bowsprit, tabernacle and chain plates are created from stainless steel. 4 aluminium deck cleats are positioned
aft & amidships with two fairleads feeding a teak Sampson publish forward. All sail controls are led aft to rope clutches / jammers with a single halyard
winch to starboard. Adjustable jib & mainsheet cars. Accessibility beneath is through a teak lined sliding companionway hatch and break up plywood / Perspex washboards.
More air flow delivered by an aluminium forward hatch.
Ports: 2 aluminium fixed ports are equipped one particular each and every in the hull topsides.
Chain plates: Chain plates are in stainless metal and by bolted on the hull sides.
Vents: Air flow is through a washboard vent and opening forward hatch.
Miscellaneous Gear: Gas filler &tank vent.(Inboard model only), Everyday living harness attachment position by the companionway, Rope tidies for halyards.
Cockpit Lockers: Two key watertight lockers with latches and padlocks are delivered. A padlock is also supplied for the companionway hatch.
Mainmast: Laminated in Sitka Spruce and handled with Sikkens Cetol which includes a stainless metal mast band to consider Cap shrouds, jib and mainsail halyards.
All deck mounted on a substantial stainless metal tabernacle.
Most important Increase: Laminated in Sitka Spruce and dealt with with Sikkens Cetol which include a Stainless metal gooseneck fitting, kicker and mainsheet bands and all
involved reefing line qualified prospects / terminals.
Bowsprit: Laminated in Sitka Spruce and taken care of with Sikkens Cetol such as a Stainless steel pivot fitting, conclude plate and bobstay get off details.
Gaff: Laminated in Sitka Spruce and dealt with with Sikkens Cetol which include a Stainless steel gaff collar with rubber defense on bearing area. Wire hoist
span and block.
Standing Rigging: Cap shrouds, reduce shrouds & forestay in 4mm 1 x 19 stainless metal wire with swagged finishes. Chromed rigging screws. Jib mounted on
reefing spar and controls led aft to cockpit.
Operating Rigging: Main throat / peak halyards – 6mm braid. Jib &Staysail halyards – 6mm braid. Principal topping elevate – 6mm braid. Mainsail reefing traces –
6mm braid. Mainsail outhaul – 6mm braid. Mainsheet & Jib sheets – 10mm sheet rope. All affiliated blocks for purchase tackles.
Mainsail: Dacron in tan or cream. 2 reef factors with tie in lacing. Luff and gaff lacing as essential.
Jib: Dacron in tan or cream with wire luff and convey to tails.
Boom Include: In maroon, or cream acrylic. Fixings to let for topping carry and mainsheet choose off. All sails provided with, sail figures, emblem and ties.
Engineering
Outboard Variation
Outboard very well: A teak motor mounting with stainless brackets. Motor well hull blank. GRP moulded gas tank stowage and gas direct splitter by means of aft
locker compartment. (fuel guide not supplied as typical)
Inboard Version
Stern Gear: A 1” stainless metal shaft is fitted, connected to the engine by means of a coupling and equipped with a Tides Maritime ‘lip seal’ gland. The shaft drives a preset
2-bladed propeller.
Engine: Yanmar 1GM10 9hp maritime diesel engine. A 55 amp (12V) alternator is equipped to the engine.
Engine Instruments and Controls: The motor devices are situated at the rear of the cockpit coaming and are recessed with a apparent protect. Instruments
include things like audible alarm, alternator warning light-weight, start out swap and cease handle. A one lever engine handle is supplied and equipped in the cockpit very well.
Engine Cooling: The motor is right salt h2o cooled. A 1/2″ diameter pipe potential customers from the main seawater inlet through a strainer to the engine and
discharges overboard by the exhaust.
Engine Exhaust: A flexible exhaust hose connects the exhaust by means of a swan neck with water trap to the outlet fitting by way of the transom.
Gas Technique: A plastic diesel tank with a capability of somewhere around 18 litres, breather and integrated gas gauge. The tank is equipped with move and return
lines, the movement line having a guide shut off valve.
Plumbing
Bilge Technique: 1 x Manual bilge pump operated from the cockpit with a handle saved in the aft locker.
Fresh Drinking water Tanks: 2 x 10ltr plastic jerry cans with manual hand pump. Also a bucket / sink.
Soil Technique: When equipped the heads discharge instantly to sea by using a vent loop and pores and skin fitting.
Inlet / Outlet Fittings: Engine: In through a single pores and skin fitting with a valve and strainer, out by means of the exhaust program.
Fuel Technique: There is a double burner hob cooker connected to a independently stored gas bottle.
12 volt DC program
Batteries: Engine – a single 12 volt 55 amp/hour. (Optional on outboard variation)
Charging: Through principal engine – a 35 amp (at 12 volt) alternator.
Switchboard: An optional switch panel is equipped to boats that have extra electronics fitted.
Miscellaneous Normal Machines
Deck: 1 x winch cope with. 1 x bilge pump manage. Stowed in aft cockpit locker. 1 x hearth extinguisher – located down underneath.
Joinery: The inside joinery is created from substantial quality elements and in accordance with good yacht follow. Bulkheads and facet back again linings are
from plywood.
Finish: All cabin woodwork is finished in a combine of painted bulkheads and varnished trim.
Soles: Rubber textured sole during.
Upholstery: A decision of soft or wipe down plastic upholstery is offered.

Posted by The Shaldives on 2021-09-18 17:43:12

Tagged: , 2021 , ABP , Arwen , Involved British Ports , bateau , bateaux , Bâteaux , Beach front , Boat , Boats , Coastal , Coastal Waters , Coastline , persuasive , compulsive , cornish crabbers , Cornish Shrimper 19 , Devon , Docks , DSC-HX60 , England , Europe , flicker , Fogwill , GB , GBR , GBTNM , Wonderful Britan , Guy , Man Fogwill , Harbour , fascinating , Maritime , Maritime , Nautical , PLAGE , River , River Teign , Rowsell Cornish Shrimper Sails , Sail Quantity 865 , Sailing Vessel , September , septembre , Shaldon , sony , Sony DSC-HX60 , South West , breathtaking , Summer , Teign Estuary , Teignbridge , Teignmouth , Teignmouth (Approaches) , the shaldives , TQ14 , United kingdom , United Kingdom , Yacht , Yachts

#household furniture #Do it yourself #woodwork #woodworking #freedownload#woodworkingprojects #woodsmith ,wood craft, wooden planer, fantastic woodworking, wooden chairs, wooden functioning resources, preferred woodworking, woodworking books, woodworking workbench designs